Alfa Romeo > 147 (00-10), 156 (97-07), GT (03-10)

表示件数:
1

(カテゴリ内:9点)

  • (PFF1-811) Front Lower Wishbone Front Bush
    (PFF1-811) Front Lower Wishbone Front Bush

    These bushes are designed to fit genuine control arms. If non genuine arms are fitted and you find the stainless steel sleeve not to fit onto the wishbone, please contact us with dimensions of the wishbone pin as you will require modified sleeves.

     

    16,740円
    注文数:
  • (PFF1-812) Front Lower Wishbone Rear Bush
    (PFF1-812) Front Lower Wishbone Rear Bush

    These bushes are designed to fit genuine control arms. If non genuine arms are fitted and you find the stainless steel sleeve not to fit onto the wishbone, please contact us with dimensions of the wishbone pin as you will require modified sleeves.



    There can be an issue with the pin diameter for PFF1-812 sleeves on non-genuine arms.

    The genuine arms have a pin diameter of 20mm, the non genuine arms have a pin diameter of 21.3mm.

    If you have arms with 21.3mm pin for the 812 bush then please telephone and we will send you replacements.

    PFF1-812 kit also comes with different sized rings. Select the correct ring depending on the rear bracket fitted.

    Use smaller ring (802b) with the aluminium bracket and 802c with the pressed steel bracket.

    It is only possible to fit these bushes after removing the arms from the car.

    For arms fitted with the pressed steel rear bracket the rubber bush may need to be burned out using a blowtorch, then the bracket cleaned up to ensure a good surface.

    WE RECOMMEND THE USE OF LOCTITE 648 OR 848 TO SECURE CENTRE SLEEVE TO ARM

    16,740円
    注文数:
  • (PFF1-810) Front Anti Roll Bar Bush
    (PFF1-810) Front Anti Roll Bar Bush
    スタビパイプ径をご確認下さい。
    8,640円
    種類:
    注文数:
  • (PFF1-815) Front Upper Arm Bush
    (PFF1-815) Front Upper Arm Bush

    These bushes should be fitted with the supplied metal washers which are to be fitted on the large “Top Hat” face of the bush.

    Always check suspension alignment after fitting POWERFLEX bushes.

     

    18,360円
    注文数:
  • (PFR1-816) Rear Suspension Front Arm Bush
    (PFR1-816) Rear Suspension Front Arm Bush

    FITTING INSTRUCTIONS FOR PFR1-816, 817, 818 REAR BUSHES

     These bushes should be fitted with the supplied washers which are to be fitted on the “top hat” face of the bush. Fit the nylon washer against the bush and the metal washer against the nylon one where applicable.

     

    On certain model cars washers may not be required if the bushes are to be mounted between two chassis faces. Always use a washer where there is no plate against the face of the bush.

    Where not fitted between two chassis faces, use large dia washer on the outside face.

    Always check suspension alignment after fitting POWERFLEX bushes.

    22,680円
    注文数:
  • (PFR1-817) Rear Suspension Rear Arm Bush
    (PFR1-817) Rear Suspension Rear Arm Bush

    FITTING INSTRUCTIONS FOR PFR1-816, 817, 818 REAR BUSHES

    These bushes should be fitted with the supplied washers which are to be fitted on the "top hat" face of the bush. Fit the nylon washer against the bush and the metal washer against the nylon one where applicable.

    On certain model cars washers may not be required if the bushes are to be mounted between two chassis faces. Always use a washer where there is no plate against the face of the bush.

    Where not fitted between two chassis faces, use large dia washer on the outside face.

    Always check suspension alignment after fitting POWERFLEX bushes

    22,680円
    注文数:
  • (PFR1-818) Rear Tie Bar to Hub Bush
    (PFR1-818) Rear Tie Bar to Hub Bush

    FITTING INSTRUCTIONS FOR PFR1-816, 817, 818 REAR BUSHES

    These bushes should be fitted with the supplied washers which are to be fitted on the “top hat” face of the bush.

    Fit the nylon washer against the bush and the metal washer against the nylon one where applicable On certain model cars washers may not be required if the bushes are to be mounted between two chassis faces.

    Always use a washer where there is no plate against the face of the bush. Where not fitted between two chassis faces, use large dia washer on the outside face.

    Always check suspension alignment after fitting POWERFLEX bushes.

    11,340円
    注文数:
  • (PFR1-819) Rear Anti Roll Bar Bush
    (PFR1-819) Rear Anti Roll Bar Bush
    スタビパイプ径をご確認下さい。
    7,830円
    種類:
    注文数:
  • (PFF1-813) Engine Mount Stabiliser Bush *V6 Only*
    (PFF1-813) Engine Mount Stabiliser Bush *V6 Only*
    V6モデルのみ適合
    11,880円
    注文数:
1

(カテゴリ内:9点)

表示件数: